主题

好友

64万

积分
扫一扫,手机访问本帖
分享到:
发表于 2016-6-18 16:05:42 |显示全部楼层 |
马上注册,结交更多好友,享用更多功能,让你轻松玩转四驱生活。 立即注册  已有账号?点击登录   关闭
Engine type — V6 cylinder, 60 degrees, SOHC 24v, MIVEC
Displacement — 2998 cc
Bore — 87.6 mm
Stroke — 82.9 mm
Compression ratio — 9.5:1
Power — 162 kW (220 PS) at 6250 rpm (169 kW / 230 PS from 2010 on)
Torque — 276 N·m (204 lb·ft) at 4000 rpm (291N·m / 215 lb·ft from 2010 on)
MIVEC switch — at 4750 rpm

Applications[edit]
2007–Present Mitsubishi Outlander
2010–Present Mitsubishi Challenger
2012–Present Mitsubishi Pajero Sport



  • The first of the main strategies used to achieve high output and low fuel consumption was to improve air intake efficiency by applying the MIVEC system (valve timing & lift switching-type), and also optimizing the intake/exhaust-ports in the cylinder head, and employing a variable intake manifold. The second strategy was to reduce mechanical friction by using an offset crankshaft and other technologies. The third strategy was to improve anti-knocking performance by more efficient cooling of the cylinder head/combustion chambers. The fourth strategy was to adopt twin knock sensors (for sensing & control in each bank) to optimize combustion.[2]
  • The 6B31 features an aluminum variable intake manifold that uses a resin-made 2-stage Induction Control Valve to provide the benefits of short and long intake tracts, automatically switching in response to engine speed. A flap inside the Induction Control Valve remains closed below 3,600 rpm, forcing the intake charge to take a longer route to the inlet valves. Over 3,600 rpm, the flap opens, providing a shorter tract to the valves to increase power. Positioning the EGR distribution inlet on the upper intake manifold, far from the throttle valve, improves real-world fuel consumption by lowering the temperature entering the EGR distribution passageway.[1]
  • A sophisticated electronically controlled multi-point fuel injection system ensures precision fuel delivery. The electronic throttle control system (throttle-by-wire) eliminates the mechanical linkage between the accelerator pedal and the throttle plate. Looping the fuel line around the engine improves exhaust gas performance by reducing fuel temperature differences between the delivery pipes, reducing pulsations within the delivery pipes, and suppressing variations in the amount of fuel injected. A combination of the MIVEC – a variable valve timing and lift system – and a two-stage variable intake manifold ensure a broad torque curve. The 6B31 provides nearly 90 percent of peak torque from just 2,000 rpm.[1]
  • The emissions of the 6B31 engine were reduced by the following means: optimization of intake/exhaust port design in the cylinder head; improvement in mixture charging efficiency and combustion stability by using the effect of the low-speed cams of MIVEC; improvement in combustion by ultra-fine atomization injectors; and the upstream heat capacity of the catalyst was reduced by adoption of the clamshell type exhaust manifold which has a built-in catalyst to make catalyst activation earlier.[2]
  • Another low-emission strategy is reducing the emissions of untreated exhaust gases directly discharged from the engine (or gases upstream of the catalyst) by the following measure: the setting of compression ratio at a rather low ratio of 9.5:1 to optimize the balance between performance and emission level; the reduction of unburned hydrocarbons in exhaust gases by the reduction of the volume of gaps in combustion-chambers where flame cannot propagate.[2]
  • The weight of the engine has been reduced by using aluminum die-casting for the cylinder block, cylinder heads and resin materials for the rocker cover and variable intake manifold. Other parts of the engine have also been made lighter, such as the use of a guideless oil level gauge, direct mounting of accessories to the engine block and shape optimization by CAE analysis.[1][2]
  • Low vibration and low noise are achieved by substantial improvement of the flexural rigidity of the powertrain (by higher stiffness of the cylinder block and oil pan), and adoption of auto-tensioner for the accessorydrive-belt, and the MIVEC system for stable combustion. Offsetting the cylinder axis of rotation in the direction of crank rotation reduces operating friction. For the air intake, lengthened ducts and optimized resonators ensure quietness and to reduce weight. A variable-valve main muffler helps reduce noise and vibration.[1][2]
  • For the 2010 model Mitsubishi upped the compression ratio of the Outlander's 6B31 to 10.5:1. This change adds an additional ten-horsepower (230 hp total) and 11 lb-ft torque (215 lb-ft total) to the engine's output.[3]
附件: 您需要 登录 才可以下载或查看,没有帐号?立即注册


四驱生活 - 综合信息
改装部落

四驱改装

汽油动力

柴油动力

轿车改装

吉普生活

旅游宿营

泡茶E族

永远经典

人过留影

站务管理

版主之家

建议区

四驱生活:『Www.4x4-life.Com』

这里聚集了爱时尚爱生活的年轻一族,队列里就差你咯,赶紧行动!

欢迎各会员在社区积极互动,文明用语、理性评论,构造文明社区。

声明:本站转载或会员发表的言论均不代表四驱生活的观点。


回复 天涯海角搜一下: 百度 谷歌 360 搜狗 搜搜 有道 谷粉 雅虎 必应 即刻

使用道具 举报

主题

好友

19

积分
  • 1新手上路
发表于 2017-6-4 18:59:41 |显示全部楼层
真的有那么一位老师每天我看到他盈利过万,他的QQ号码是:198308067。
回复

使用道具 举报

使用高级模式(可批量传图、插入视频等)快速回复

您需要登录后才可以回帖 登录 | 立即注册

  Ctrl + Enter 快速发布 

发帖时请遵守我国法律,网站会将有关你发帖内容、时间以及发帖IP地址等记录保留,只要接到合法请求,即会将信息提供给有关政府机构。
返回顶部快速回复上一主题下一主题返回列表找客服手机访问
客服中心
关闭
联系电话:
021-58673385
Email:
767892288@qq.com
QQ群:111837168
网址:四驱生活
售后
技术支持
网店
客服中心

找客服

回顶部